RSGen2 ESC 17.5 Gen3 Sensored BL Motor System
This part is discontinued and we no longer carry it.
Description
This is the Tekin Gen 3 Brushless Sensored 17.5T Motor and the
RS Gen 2 Spec Brushless Electronic Speed Control.
TT2705 Motor (TEKC2705);
CNC machined T 6061 billet aluminum heat sink can
For on- or off-road use
12.5mm performance rotor
Dual-plug sensor wire harness for all sensored and sensorless systems
Anodized end-bell plates maximize corrosion and wear resistance
High RPM precision ball bearings
Neodymium sintered magnet
Rebuildable
Adjustable timing
Low resistance solder tabs
Solderless sensor PCB replacement
ESC;
Compatible with sensored, sensorless, brushless, and brushed motors
Datalogging capability
High voltage programmable Battery Eliminator Circuit (BEC)
HotWire PC interface for advanced programming and updating, EZ access
programming port (HotWire Interface (TEKM1450), and Gen 2 Adaptor
(TEKM3825) required)
Forward, brake, and reverse operation
D2 Dual Drive Mode technology
On-board temperature indicator
Sensor plug for precise commutation with all motors
Gold plated solder posts
Pit tune mode
HDAC: High Density Copper PCBs
Self test diagnostics and factory reset
DGF2 Digital Glitch Filtering V2
QuickTune programming with one-touch radio calibration
120 day limited warranty through Tekin beginning at date of purchase
Wires
Redline GEN3 17.5 Turn Brushless Sensored Motor with Sensor Wire
ESC;
Input Voltage: 4-9 cells, 2-3S LiPo
BEC: 6.0V / 7.4V @ 5.5A
Motor Limit Brushless Mode 2S: 8.5T 2-Pole 36mm Can
Motor Limit Brushless Mode 3S: 10.5T 2-Pole 36mm Can
Motor Limit Brushed Mode 2S: 12 Turn 36mm Can
Motor Limit Brushed Mode 3S: 20 Turn 36mm Can
Max Current: 120amps per phase
Max Chassis Weight: 4lbs (1815g)
Throttle Profiles: 7 choices on-board
Brushed Modes: Fwd Only, Fwd/Rev, Rev Delay
Brushless Modes: Fwd Only, Fwd/Rev, Rev Delay
Weight: .85oz (24g)
17.5T Motor;
Input Voltage: 2S all, 3S-10.5 and up
Shaft
Weight: 5.6oz (158g)
Motor Diameter: 1.40" (35.85mm)
Motor Length: 1.9" (48.5mm)
Bearing
Rotor Size: 12.5mm
RS Gen 2 Spec Brushless Electronic Speed Control.
FEATURES:
CNC machined T 6061 billet aluminum heat sink can
For on- or off-road use
12.5mm performance rotor
Dual-plug sensor wire harness for all sensored and sensorless systems
Anodized end-bell plates maximize corrosion and wear resistance
High RPM precision ball bearings
Neodymium sintered magnet
Rebuildable
Adjustable timing
Low resistance solder tabs
Solderless sensor PCB replacement
ESC;
Compatible with sensored, sensorless, brushless, and brushed motors
Datalogging capability
High voltage programmable Battery Eliminator Circuit (BEC)
HotWire PC interface for advanced programming and updating, EZ access
programming port (HotWire Interface (TEKM1450), and Gen 2 Adaptor
(TEKM3825) required)
Forward, brake, and reverse operation
D2 Dual Drive Mode technology
On-board temperature indicator
Sensor plug for precise commutation with all motors
Gold plated solder posts
Pit tune mode
HDAC: High Density Copper PCBs
Self test diagnostics and factory reset
DGF2 Digital Glitch Filtering V2
QuickTune programming with one-touch radio calibration
120 day limited warranty through Tekin beginning at date of purchase
YOU WILL RECEIVE:
RS Gen 2 Spec Brushless ESC with Instructions, Motor and Receiver Wires
Redline GEN3 17.5 Turn Brushless Sensored Motor with Sensor Wire
SPECIFICATIONS:
Input Voltage: 4-9 cells, 2-3S LiPo
BEC: 6.0V / 7.4V @ 5.5A
Motor Limit Brushless Mode 2S: 8.5T 2-Pole 36mm Can
Motor Limit Brushless Mode 3S: 10.5T 2-Pole 36mm Can
Motor Limit Brushed Mode 2S: 12 Turn 36mm Can
Motor Limit Brushed Mode 3S: 20 Turn 36mm Can
Max Current: 120amps per phase
Max Chassis Weight: 4lbs (1815g)
Throttle Profiles: 7 choices on-board
Brushed Modes: Fwd Only, Fwd/Rev, Rev Delay
Brushless Modes: Fwd Only, Fwd/Rev, Rev Delay
DIMENSIONS:
1.0 x 1.3 x .51" (26 x 34 x 12.9mm) Weight: .85oz (24g)
17.5T Motor;
Input Voltage: 2S all, 3S-10.5 and up
Shaft
DIMENSIONS:
3.2mm (1/8") x 15.3mm Weight: 5.6oz (158g)
Motor Diameter: 1.40" (35.85mm)
Motor Length: 1.9" (48.5mm)
Bearing
DIMENSIONS:
Front: 4x13x5mm / Rear: 1/8x3/8x5/32" Rotor Size: 12.5mm
Manufacturer information
Alternate part numbers
Here are some alternate part numbers and product codes that you may find this part listed under on other sites:
TT2733
0706893027338
TEKC2733
706893027338
Additional details
Shipping weight
10.40 ounces
294.83 grams
0.65 pounds
Package dimensions
5.50 x 4.50 x 2.00
⚠️ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov ⚠️